Intellicharg Series |  3-Stage Battery Charger

12V, 24V and 48V DC Models, 360W

The ICT IntelliCharge Series is a high efficiency, power factor corrected DC power supply and battery charger that allows the battery charge to be regulated independently from the DC outputs, meaning that the battery will always receive the optimal charging current without the load being affected. Available with optional OLED high-resolution display and 1RU 19 inch rack mounting kit. Temperature-compensated charging is supported with the optional battery temp sensor.

  • Operates as a DC UPS, providing uninterrupted DC power to critical loads, even when AC mains fail
  • Wide-ranging power factor corrected AC input helps reduce energy costs and works anywhere in the world
  • Intelligent three-stage charging recharges battery quickly and maintains it in optimal condition
  • 12, 24 and 48 volt DC models with 360 watts of power output
  • Independent battery backup charging terminals with internal Low Voltage Disconnect
  • User-selectable battery type sets charge cycle transitions for use with standard Flooded, AGM and Gel lead-acid batteries
  • User-definable bulk charge current setting
  • Form C alarm contacts provide remote signal of fault conditions
  • Temperature-compensated charging with optional battery temperature sensor
  • Compact design allows for mounting one or two units in an optional 1RU rack kit
  • Optional high-resolution OLED display provides real-time information on current, voltage and charge status

High Reliability

  • Designed around the highest quality components available
  • Two-year warranty
  • Form C contacts provide remote alarm monitoring

Options

Remote Battery Temperature Sensor: 2 wire remote temperature sensor with 10 ft (3m) cable and mounting clip. Will enable charge voltage thresholds to be automatically compensated according to the measured battery case temperature.

AC Input Connector: IEC 320-C14

Digital Meter Optional: OLED digital display provides voltage, current and charging status. Must be specified at the time of ordering.

DIN Rail Mounting Accessory Available

Wall Mount Bracket: Formed rails with holes for mounting unit to shelf or wall. Attaches to sides of the unit with included fasteners.

19” Rack Mount Kit: Allows one or two IntelliCharge power supplies to be mounted in a 1RU 19” rack.

SERIES TABLE

Model NumberOutput PowerOutput VoltageDigital Meter
ICT24012A-30BC2M360W12VYes
ICT24024A-15BC2M360W24VYes
ICT24048A-7BC2M360W48VYes
ICT24012A-30BC2360W12VNo
ICT24024A-15BC2360W24VNo
ICT24048A-7BC2360W48VNo

 

Other Components
Remote Battery Temperature SensorICT-TMP
19 “ Rack Mount Tray (holds 1 or 2 IntelliCharge units)ICT-RM1U / RM2U

SPECIFICATIONS TABLE

Electrical
Continuous Output Current – 12V30A
Continuous Output Current – 24V15A
Continuous Output Current –  48V7.5A
Efficiency (typical) – 12V90% @ 220VAC
Efficiency (typical) – 24V91% @ 220VAC
Efficiency (typical) – 48V93% @ 230VAC
Default Output Float Voltage – 12V13.65VDC
Default Output Float Voltage – 24V27.3VDC
Default Output Float Voltage – 48V54.6VDC
Input Voltage Range100-265VAC
Frequency Range50/60Hz
Power Factor (typical)0.99
Output Ripple – all models<50mV RMS
Mechanical
Dimensions L x W x H7.9 x 5.9 x 1.8 inches / 200 x 149 x 46 mm
Weight2.61 lbs / 1.19 kg
AC Input ConnectorsIEC 320-C14
DC Output Connectors4 position terminal block
Remote Alarm Connectors5 position pluggable wire clamp connector
Battery Management
LVD Disconnect Voltage – 12V11.0VDC
LVD Disconnect Voltage – 24V22.0VDC
LVD Disconnect Voltage – 48V44.0VDC
LVD Reconnect Voltage – 12V12.5VDC
LVD Reconnect Voltage – 24V25.0VDC
LVD Reconnect Voltage – 48V50.0VDC

You may also like...